The beam specifications of the new tarm 13 are given with only ca. 5.0 mm diameter and 0.8 mrad divergence – which applies to both axis. The extremely small beam diameter allows for the use of very small 4.5 mm mirrors, which results in reduced inertia and thus very good scanning performance.

The tarm 13 impresses with a guaranteed RGB output power of 13’000 mW. Great visibility is achieved with the new RTI Semiconductor Laser modules (RSL) with special wavelengths for increased visibility: 4,000 mW / 637 nm for a very bright red combined with 5,800 mW / 525 nm green and a strong blue laser module with 5,000 mW / 455 nm. The 525nm green provides a warmer green tone than the 520nm diodes and has increased visibility.
These new RSL modules with their extremely low divergence and homogenous beam shape make the tarm 13 a top professional laser system. The extremely small beam diameter of only ca. 5.0 mm allows for the use of small scanner mirrors which leads to reduced inertia and higher scan speeds. This is especially important, as the tarm 13 can be used for any kind of laser show application: Super sharp beams and vivid colors for large scale concerts and festivals but also a perfectly matched beam for crisp graphics.

The RTI Semiconductor Laser modules are maintenance free and do not come out of internal alignment.
The standard scanners can be run at a maximum of 45kpps @ 8° ILDA and a maximum scan angle of 50°. CT-6210 scanners with LAS Turboscan drivers are available as option and provide even higher scan speeds with up to 60kpps at 8° ILDA .

The powerful tarm 13 is suitable for indoor and outdoor show laser applications at concerts, festivals and other huge events. Demanding graphics projections or projections over long distances are possible without any problems, due to the extremely good divergence.

Including ShowNET Mainboard

The tarm 13 is delivered with a ShowNET laser mainboard as standard. This means it has a multitude of control features already built-in: Control via DMX or ArtNET, just like a normal lighting fixture, are possible as well as computer control via ILDA or LAN. Of course the laser can be run in stand alone operation, too. The contents for playback (for DMX, ArtNet, Stand-Alone, etc.) can be fully customized. As the ShowNET laser mainboard comes with a full license of the Showeditor software, it is easy to create custom content for the built-in memory or even directly control the laser with a computer – either live or for creation an playback of complete laser shows.

If ILDA shall be used as control option, like from an external Lasergraph DSP, the internal ShowNET mainboard can also be used as receiver for an ILDA streaming signal – so the externbal ILDA signal can be feeded to an external ShowNET device and this sends the direct control to the tarm 13 via ILDA Streaming – so no long ILDA cables are required any more, even with ILDA based control systems.

The beam specifications of the new tarm 25 are given with only ca. 5.0 mm diameter and <0.8 mrad divergence – which applies to both axis. The extremely small beam diameter allows for the use of very small 4.5 mm mirrors, which results in reduced inertia and thus very good scanning performance.

The tarm 25 impresses with a guaranteed RGB output power of 24’500 mW. Great visibility is achieved with the new RTI Semiconductor Laser modules (RSL) with special wavelengths for increased visibility: 7’500 mW / 637 nm for a very bright red combined with 12’000 mW / 525 nm green and a strong blue laser module with 10’000 mW / 455 nm. The 525nm green provides a warmer green tone than the 520nm diodes and has increased visibility.
These new RSL modules with their extremely low divergence and homogenous beam shape make the tarm 25 a top professional laser system. The extremely small beam diameter of only ca. 5.0 mm allows for the use of small scanner mirrors which leads to reduced inertia and higher scan speeds. This is especially important, as the tarm 25 can be used for any kind of laser show application: Super sharp beams and vivid colors for large scale concerts and festivals but also a perfectly matched beam for crisp graphics.

The RTI Semiconductor Laser modules are maintenance free and do not come out of internal alignment.
The standard scanners can be run at a maximum of 45kpps @ 8° ILDA and a maximum scan angle of 50°. CT-6210H scanners with LAS Turboscan drivers are available as option and provide even higher scan speeds with up to 60kpps at 8° ILDA .

The powerful tarm 25 is suitable for indoor and outdoor show laser applications at concerts, festivals and other huge events. Demanding graphics projections or projections over long distances are possible without any problems, due to the extremely good divergence.

Including ShowNET Mainboard

The tarm 25 is delivered with a ShowNET laser mainboard as standard. This means it has a multitude of control features already built-in: Control via DMX or ArtNET, just like a normal lighting fixture, are possible as well as computer control via ILDA or LAN. Of course the laser can be run in stand alone operation, too. The contents for playback (for DMX, ArtNet, Stand-Alone, etc.) can be fully customized. As the ShowNET laser mainboard comes with a full license of the Showeditor software, it is easy to create custom content for the built-in memory or even directly control the laser with a computer – either live or for creation an playback of complete laser shows.

If ILDA shall be used as control option, like from an external Lasergraph DSP, the internal ShowNET mainboard can also be used as receiver for an ILDA streaming signal – so the externbal ILDA signal can be feeded to an external ShowNET device and this sends the direct control to the tarm 11 via ILDA Streaming – so no long ILDA cables are required any more, even with ILDA based control systems.

The beam specifications of the new tarm 11 are given with only ca. 5.0 mm diameter and 0.7 mrad divergence – which applies to both axis. The extremely small beam diameter allows for the use of very small 4.5 mm mirrors, which results in reduced inertia and thus very good scanning performance.

The tarm 11 impresses with a guaranteed RGB output power of 11’000 mW. Great visibility is achieved with the new RTI Semiconductor Laser modules (RSL) with special wavelengths for increased visibility: 3’500 mW / 637 nm for a very bright red combined with 5’000 mW / 525 nm green and a strong blue laser module with 4’000 mW / 455 nm. The 525nm green provides a warmer green tone than the 520nm diodes and has increased visibility.
These new RSL modules with their extremely low divergence and homogenous beam shape make the tarm 11 a top professional laser system. The extremely small beam diameter of only ca. 5.0 mm allows for the use of small scanner mirrors which leads to reduced inertia and higher scan speeds. This is especially important, as the tarm 11 can be used for any kind of laser show application: Super sharp beams and vivid colors for large scale concerts and festivals but also a perfectly matched beam for crisp graphics.

The RTI Semiconductor Laser modules are maintenance free and do not come out of internal alignment.
The standard scanners can be run at a maximum of 45kpps @ 8° ILDA and a maximum scan angle of 50°. CT-6210 scanners with LAS Turboscan drivers are available as option and provide even higher scan speeds with up to 60kpps at 8° ILDA .

The powerful tarm 11 is suitable for indoor and outdoor show laser applications at concerts, festivals and other huge events. Demanding graphics projections or projections over long distances are possible without any problems, due to the extremely good divergence.

Including ShowNET Mainboard

The tarm 11 is delivered with a ShowNET laser mainboard as standard. This means it has a multitude of control features already built-in: Control via DMX or ArtNET, just like a normal lighting fixture, are possible as well as computer control via ILDA or LAN. Of course the laser can be run in stand alone operation, too. The contents for playback (for DMX, ArtNet, Stand-Alone, etc.) can be fully customized. As the ShowNET laser mainboard comes with a full license of the Showeditor software, it is easy to create custom content for the built-in memory or even directly control the laser with a computer – either live or for creation an playback of complete laser shows.

If ILDA shall be used as control option, like from an external Lasergraph DSP, the internal ShowNET mainboard can also be used as receiver for an ILDA streaming signal – so the externbal ILDA signal can be feeded to an external ShowNET device and this sends the direct control to the tarm 11 via ILDA Streaming – so no long ILDA cables are required any more, even with ILDA based control systems.

The climate housing has an integrated temperature sensor which automatically starts the cooling function as soon as a certain temperature is exceeded. This ensures the optimal operating temperature of the laser system. In addition, the tarm OUTDOOR system protects against low temperatures (up to – 5°C) by activating an integrated heater at an ambient temperature of +10°C and below. This ensures the optimal operating temperature of the laser and prevents undercooling and damage to the laser as well as impact on output quality.

These effects can be created:
– Burst grating (grid)
– Line grating (line split)
– Lumia (Striae, Light refraction) – Open (let pass the normal projection)

The tarm Gobo Wheel allows for a maximum scan angle of 55°

The tarm Gobo Wheel can simply be placed in front (and party atop) of a laser system. It suits most tarm and Laserworld laser systems, but can also be used with other models.

Important:
No laser system is included with this product. This product is an accessory to a laser system. Effects pictures have been created with a tarm laser system for showcase purposes, however the laser system is not included with this product!

The tarm 3 units have a built-in network DAC for Showcontroller and Showeditor, but also can be controlled with any ILDA laser control software such as Pangolin Quickshow, Pangolin Beyond, LSX, Lasergraph DSP, etc. via external ILDA interface (e.g. FB3). They also have a built-in memory with pre-set patterns, that can be easily triggered through DMX and automatic mode.

The tarm 3 laser has great beam specifications with a diameter of ca. ca. 4.5 mm and a beam divergence of less than 0.6 mrad (full angle).
It is equipped with a bright red (1,000 mW / 637 nm), a green (900 mW / 520 nm), and a blue (1,700 mW / 450 nm) diode laser source.

The scanners are very fast with 45kpps @ 8° ILDA standard and allow for a maximum scan angle of 50°. Thus they are well graphics capable and suitable for professional laser applications.
Optionally as upgrade available: CT-6210 scanners with 60 kpps@8° ILDA and a max. scan angle of 60°.

This show laser light has a switchable scan safety.

The housing of the tarm 3 is built very rugged and in a dust-proof way, so there is no air circulation inside the enclosure. This reduces maintenance efforts to a minimum.
The mounting bracket allows for hanging and for upright mounting of the laser system.

The tarm 3 is especially suitable for show laser applications in clubs and bars and can be used by beginners as well as professionals.

Integrated ShowNET incl. free laser show software

The tarm 3 features an integrated ShowNET network interface with free laser control software included!
Start with your own professional laser show thanks to the intuitive Showeditor laser show software which comes with every new tarm 3 for free. The Showcontroller software is supported as well and can be purchased additionally.
The integrated ShowNET allows for direct input through ILDA and LAN. Besides DMX, it is possible to trigger single frames via ArtNet. Custom frames and shows can be played from an integrated SD card (included in delivery) – even in stand-alone mode!

There are two different DMX modes:
(1) DJ Mode with the most used features for beginners. Only a few DMX channels are used for a quick and easy access to the most important adjustments directly at the laser system.
(2) Professional Mode with all DMX features especially for users with a DMX console. All adjustments can be triggered and allow for full control of the professional laser show.
The integrated ShowNET works as DAC (digital to analog converter) and enables ILDA streaming.

The Tarm 6 units have a built-in network DAC for Showcontroller and Showeditor, but also can be controlled with any ILDA laser control software such as Pangolin Quickshow, Pangolin Beyond, LSX, Lasergraph DSP, etc. via external ILDA interface (e.g. FB3). They also have a built-in memory with pre-set patterns, that can be easily triggered through DMX, automatic mode.
The Tarm 6 comes with integrated ShowNET network interface and free laser show software. Details in the box below.

The benefits include:

• 6’000 mW guaranteed output power
• a very fast maximum scan speed of 45kpps @ 8° ILDA for graphics projection
• high-precision diode arrays provide an excellent beam divergence of less than <0.6 mrad for a low beam diameter
• pure diode laser
• novel method for increasing the beam precision of the single-mode diodes
• beautiful colors and great color fading
• the tarm 6 impresses with a very bright 637 nm single mode red
• MANUFACTURED IN GERMANY, with high precision diodes array modules.

The tarm 6 has good specifications with a beam diameter of ca. 4.5 mm and a beam divergence of less than <0.6 mrad (full angle).
It is equipped with a red (2’000 mW / 637 nm), a green (1’800 mW / 520 nm), and a blue (3’200 mW / 450 nm) diode laser source.

The tarm 6 devices have very fast scanners, running at 45kpps @ 8° ILDA and scanning a maximum scan angle of 50°, upgrades to CT-6210 scanners with 60 kpps@8° ILDA and a deflection angle of up to 60° are available on request. These specifications definitely make the units perfectly suitable for professional applications and ideal for graphics projections.

The housing of the tarm 6 is built very rugged and in a dust-proof way, so there is no air circulation inside the enclosure. This reduces maintenance efforts to a minimum. The mounting bracket allows for hanging and for upright mounting of the laser system.

The tarm 6 is suitable for demanding show laser applications and graphics projections in clubs, bars and on small stages and can be used by beginners as well as professionals.

+ Integrated ShowNET incl. free laser show software

The tarm 6 features an integrated ShowNET network interface with free laser control software included!
Start with your own professional laser show thanks to the intuitive Showeditor laser show software which comes with every new tarm 6 for free. The Showcontroller software is supported as well and can be purchased additionally.
The integrated ShowNET allows for direct input through ILDA and LAN. Besides DMX, it is possible to trigger single frames via ArtNet. Custom frames and shows can be played back from an integrated SD card (included in delivery) – even in stand-alone mode!
There are two different DMX modes:
(1) DJ Mode with the most used features for beginners. Only a few DMX channels are used for a quick and easy access to the most important adjustments directly at the laser system.
(2) Professional Mode with all DMX features especially for users with a DMX console. All adjustments can be triggered and allow for full control of the professional laser show.
The integrated ShowNET works as DAC (digital to analog converter) and enables ILDA streaming.