The Laserworld CS-12.000RGB FX MK2 has two grating effects built in in addition to the graphics capable scanners: line grating and burst grating .
Together with the ca. 130 (layers, tunnels, fences, waves, etc.), effects gratings stored on the laser, these effects offer a variety of combinations for impressive illumination of medium-sized to large locations. The grating effects make the projected patterns appear as if they were displayed by many projectors at the same time, resulting in unique and eyecatching visual effects. 

The Laserworld CS-12.000RGB FX MK2 is a pure diode, analog modulated, full color RGB laser system with a total output power of up to 12,000 mW and a guaranteed output power of 11,000 mW. This is split over the three primary colour modules;  Red: 2,600 mW / 638 nm, Green: 2,900 mW / 520 nm and Royal-Blue: 5,500 mW / 450 nm. The pure diode laser sources ensure more uniform and powerful laser beams with enhanced colour mixing options. The projector has good beam specifications with a beam diameter of 5 mm and beam divergence of 1.4 mrad. The galvo system has a scan speed of up to 28kpps @ 8° ILDA, galvo system, switchable effects grating wheel.

Pattern size can be set by two rotary buttons on the rear side of the housing. The sensitivity of the microphone can be adjusted via the integrated display.

There is no airflow in the optical compartment, the temperature is regulated through the separate cooling fins compartment. This reduces maintenance and cleaning requirements to a minimum.

Through DMX, in the stand-alone mode as well as in the sound-to-light mode about ca. 130 (layers, tunnels, fences, waves, etc.), effects gratings can be projected in different colors and in various speed. If the stand-alone mode is active, the pre-programmed patterns run without assistance and in the sound-to-light mode, the laser system projects according to the sound.

Next to the modes mentioned above, this laser projector provides a master-slave-mode. Show lasers of the same series (slave projectors), connected via DMX cable to a main projector (master projector) project the same patterns like the master projector.

The Laserworld CS-12.000RGB FX MK2 is computer controllable through a professional ILDA interface. Thus own or pre-programmed lasershows, logos, texts or own graphics and animations can be shown in combination with a laser control software (e.g. Showeditor or Showcontroller).

There are safety features like a key switch, an interlock and an on-off switch.

The Laserworld CS-12.000RGB FX MK2 show laser projector comes with a compact housing, which is light weight and has a stable bracket. The 360° mounting bracket allows for different mounting positions: a hanging as well as a standing installation is possible – ideal for mobile DJs and temporary laser shows, but also for fixed installations at a truss or at the ceiling.

The Laserworld CS-12.000RGB FX MK2 is ideal for semi-professional applications and is perfectly suitable in medium sized to large clubs and discos as well as for mobile DJs, private use and in any other party location.

The Laserworld CS-24.000RGB FX has three grating effects built in in addition to the graphics capable scanners: line grating, radial grating and burst grating .
Together with the ca. 130 (layers, tunnels, fences, waves, etc.), effects gratings stored on the laser, these effects offer a variety of combinations for impressive illumination of medium-sized to large locations. The grating effects make the projected patterns appear as if they were displayed by many projectors at the same time. The resulting extensiveness allows for effects that could not be achieved in any other way.
But that’s not everything the Laserworld CS-24.000RGB FX has to offer:

The Laserworld CS-24.000RGB FX is a pure diode, analog modulated, full color RGB laser system with a total output power of up to 22’200 mW and a guaranteed output power of 22’000 mW. The red laser source has an output power of 5’000 mW / 638 nm, the green of 5’200 mW / 520 nm and the royal-blue laser source has an output power of 12’000 mW / 450 nm. The diode laser sources ensure powerful laser beams. The projector has good beam specifications with a beam diameter of ca. 6 mm and beam divergence of 1.4 mrad. The galvo system has a scan speed of up to 28kpps @ 8° ILDA, galvo system, switchable effects grating wheel.

Pattern size can be set by two rotary buttons on the rear side of the housing. The sensitivity of the microphone can be adjusted via the integrated display.

There is no airflow in the optical compartment, the temperature is regulated through the separate cooling fins compartment. This reduces maintenance and cleaning requirements to a minimum.

Through DMX, in the stand-alone mode as well as in the sound-to-light mode about ca. 130 (layers, tunnels, fences, waves, etc.), effects gratings can be projected in different colors and in various speed. If the stand-alone mode is active, the pre-programmed patterns run without assistance and in the sound-to-light mode, the laser system projects according to the sound.

Next to the modes mentioned above, this laser projector provides a master-slave-mode. Show lasers of the same series (slave projectors), connected via DMX cable to a main projector (master projector) project the same patterns like the master projector.

The Laserworld CS-24.000RGB FX is computer controllable through a professional ILDA interface. Thus own or pre-programmed lasershows, logos, texts or own graphics and animations can be shown in combination with a laser control software (e.g. Showeditor or Showcontroller).

There are safety features like a key switch, an interlock and an on-off switch.

The Laserworld CS-24.000RGB FX show laser projector comes with a compact housing, which is light weight and has a stable bracket. The 360° mounting bracket allows for different mounting positions: a hanging as well as a standing installation is possible – ideal for mobile DJs and temporary laser shows, but also for fixed installations at a truss or at the ceiling.

The Laserworld CS-24.000RGB FX is ideal for semi-professional applications and is perfectly suitable in large clubs and discos as well as for festivals or larger stages and generally outdoor events.

CS-4000RGB FX is a pure-diode, analog-modulated, full-colour RGB laser system. It has a total output power of up to 4,000 mW and guaranteed output power of 3,500 mW. CS-4000RGB’s red laser has an output power of 850 mW / 635 nm. Its green laser has an output of 850 mW / 520 nm and the royal-blue laser has an output power of 1’800 mW / 450 nm.

Because of its powerful diode-laser source, this laser is much more visible than most standard lasers. Additionally, the projector has a beam diameter of ca. 3 mm and beam divergence of 1.4 mrad. The CS-4000RBB’s galvo system has a scan speed of up to 28kpps @ 8° ILDA.

CS-4000RGB has layers, tunnels, fences, waves and more, stored on the laser, these effects offer a variety of combinations for impressive illumination. Afterwards, utilise the grating effects to make the projected patterns appear as if they were displayed by many projectors at the same time. As a result, you can create a unique light show and pattern that would not be able to be achieved in any other way

Adjust the pattern size by two rotary buttons on the rear side of the housing. Furthermore, adjust the sensitivity of the microphone for automatic modes via the integrated display. Taking a look inside, there is no airflow in this laser’s optical compartment as its temperature is regulated via the separate cooling-fins compartment. This therefore reduces maintenance and cleaning requirements to a minimum.

Control the CS-4000RGB through DMX, stand-alone mode as well as in the sound-to-light mode. When doing so, you can project in different colours and in various speeds. Also, if the stand-alone mode is active, the pre-programmed patterns run without assistance. However, if the unit is in the “sound-to-light” mode, the laser system projects according to the sound.

Additionally, this laser projector provides a master-slave mode. After that, control the CS-4000RGB FX by a computer through a professional ILDA interface. Thus, you can pre-program laser shows, and use logos, texts or your own graphics and animations with laser control software (e.g. Showeditor or Showcontroller).

CS-4000RGB comes with safety features like a key switch, an interlock and an on-off switch. Also, this laser has compact housing, which is lightweight and comes with a stable bracket attatched. The 360° mounting bracket allows for different mounting positions, ideal for mobile DJs and temporary laser shows, but also for fixed installations at a truss or at the ceiling.

The Laserworld CS-8000RGB FX has two grating effects built in in addition to the graphics capable scanners: line grating and burst grating .
Together with the ca. 130 (layers, tunnels, fences, waves, etc.), effects gratings stored on the laser, these effects offer a variety of combinations for impressive illumination of medium-sized to large locations. The grating effects make the projected patterns appear as if they were displayed by many projectors at the same time. The resulting extensiveness allows for effects that could not be achieved in any other way.
But that’s not everything the Laserworld CS-8000RGB FX has to offer:
The Laserworld CS-8000RGB FX is a pure diode, analog modulated, full color RGB laser system with a total output power of up to 8’000 mW and a guaranteed output power of 7’300 mW. The red laser source has an output power of 1’800 mW / 638 nm, the green of 1’800 mW / 520 nm and the royal-blue laser source has an output power of 3’700 mW / 450 nm. The diode laser sources ensure powerful laser beams. The projector has good beam specifications with a beam diameter of 5 mm and beam divergence of 1.4 mrad. The galvo system has a scan speed of up to 28kpps @ 8° ILDA, galvo system, switchable effects grating wheel.

Pattern size can be set by two rotary buttons on the rear side of the housing. The sensitivity of the microphone can be adjusted via the integrated display.

There is no airflow in the optical compartment, the temperature is regulated through the separate cooling fins compartment. This reduces maintenance and cleaning requirements to a minimum.

Through DMX, in the stand-alone mode as well as in the sound-to-light mode about ca. 130 (layers, tunnels, fences, waves, etc.), effects gratings can be projected in different colors and in various speed. If the stand-alone mode is active, the pre-programmed patterns run without assistance and in the sound-to-light mode, the laser system projects according to the sound.

Next to the modes mentioned above, this laser projector provides a master-slave-mode. Show lasers of the same series (slave projectors), connected via DMX cable to a main projector (master projector) project the same patterns like the master projector.

The Laserworld CS-8000RGB FX is computer controllable through a professional ILDA interface. Thus own or pre-programmed lasershows, logos, texts or own graphics and animations can be shown in combination with a laser control software (e.g. Showeditor or Showcontroller).

There are safety features like a key switch, an interlock and an on-off switch.

The Laserworld CS-8000RGB FX show laser projector comes with a compact housing, which is light weight and has a stable bracket. The 360° mounting bracket allows for different mounting positions: a hanging as well as a standing installation is possible – ideal for mobile DJs and temporary laser shows, but also for fixed installations at a truss or at the ceiling.

The Laserworld CS-8000RGB FX is ideal for semi-professional applications and is perfectly suitable in medium sized to large clubs and discos as well as for mobile DJs, private use and in any other party location.

The Laserworld CS-2000RGB FX MKII has three grating effects built in in addition to the graphics capable scanners: line grating, burst grating and radial grating.
Together with the ca. 130 (layers, tunnels, fences, waves, etc.) stored on the laser, these effects offer a variety of combinations for impressive illumination of medium-sized to large locations. The grating effects make the projected patterns appear as if they were displayed by many projectors at the same time. The resulting extensiveness allows for effects that could not be achieved in any other way.
But that’s not everything the Laserworld CS-2000RGB FX MKII has to offer:

The Laserworld CS-2000RGB FX MKII is a pure diode, analog modulated, full color RGB laser system with a total output power of up to 2’000 mW and a guaranteed output power of 1’600 mW. The red laser source has an output power of 250 mW / 635 nm, the green of 250 mW / 520 nm and the royal-blue laser source has an output power of 1’100 mW / 450 nm. The diode laser sources ensure powerful laser beams. The projector has good beam specifications with a beam diameter of ca. 3 mm and beam divergence of 1.4 mrad. The galvo system has a scan speed of up to 28kpps @ 8° ILDA.

Pattern size can be set by two rotary buttons on the rear side of the housing. The sensitivity of the microphone can be adjusted via the integrated display.

Through DMX, in the stand-alone mode as well as in the sound-to-light mode about ca. 130 (layers, tunnels, fences, waves, etc.) can be projected in different colors and in various speed. If the stand-alone mode is active, the pre-programmed patterns run without assistance and in the sound-to-light mode, the laser system projects according to the sound.

Next to the modes mentioned above, this laser projector provides a master-slave-mode. Show lasers of the same series (slave projectors), connected via DMX cable to a main projector (master projector) project the same patterns like the master projector.

The Laserworld CS-2000RGB FX MKII is computer controllable through a professional ILDA interface. Thus own or pre-programmed lasershows, logos, texts or own graphics and animations can be shown in combination with a laser control software (e.g. Showeditor or Showcontroller).

There are safety features like a key switch, an interlock and an on-off switch.

The Laserworld CS-2000RGB FX MKII show laser projector comes with a compact housing, which is light weight and has a stable bracket. The 360° mounting bracket allows for different mounting positions: a hanging as well as a standing installation is possible – ideal for mobile DJs and temporary laser shows, but also for fixed installations at a truss or at the ceiling.

The Laserworld CS-2000RGB FX MKII is ideal for semi-professional applications and is perfectly suitable in medium sized to large clubs and discos as well as for mobile DJs, private use and in any other party location.

The Laserworld CS-1000RGB MKIII show laser projector comes with a completely new designed compact housing, which is light weight and has a stable bracket. The solid bracket allows for different mounting positions: a hanging as well as a standing installation is possible – ideal for mobile DJs and temporary laser shows, but also for fixed installations at a truss or at the ceiling.

The Laserworld CS-1000RGB MKIII is a pure diode multi color RGB laser system with a total output power of up to 1’000 mW and a guaranteed output power of 800 mW. The red laser source has an output power of 200 mW / 650 nm, the green 70 mW / 520 nm and the royal-blue laser source has an output power of 530 mW / 450 nm. The laser sources ensure brilliant colors and powerful laser beams. The projector has good beam specifications with ca. 3 mm / 1.1 mrad. The galvo system has a scan speed of up to 28 kpps @ 8° ILDA.

Pattern size can be set by two rotary buttons (X and Y axis) on the rear side of the housing. The sensitivity of the microphone can be adjusted via the integrated display.

Through DMX, in the automatic mode as well as in the sound-to-light mode ca. 130 (layers, tunnels, fences, waves, etc.) can be projected in different colors and in various speed. If the automatic mode is active, the pre-programmed patterns run without assistance and in the sound-to-light mode, the laser system projects according to the sound.

Next to the modes mentioned  above, this laser projector provides a master-slave-mode. Show lasers of the same series (slave projectors), connected via DMX to a main projector (master projector) project the same patterns like the master projector.

The Laserworld CS-1000RGB MKIII is computer controllable through a professional ILDA interface. Thus custom or pre-programmed lasershows, logos, texts or own graphics and animations can be shown in combination with a laser control software.

There are safety features like a key switch, an interlock connector and an on-off switch.

The Laserworld CS-1000RGB MKIII is ideal for small to semi-professional applications and is perfectly suitable in bars, small to medium sized clubs and discos as well as for mobile DJs, private use and in any other party location.

Powering the laser projector are 3 primary modules; Red, Green, and Blue. The red diode laser module with a wavelength of 650 nm, the green DPSS laser module with a wavelength of 532nm, the royal-blue laser module with a wavelength of 445 nm ensure beautiful colors and brightness. The projector offers high-speed stepper motors with 15 kpps at 4°, with a max scan angle of up to 20°. For great coverage and effect.

For the best effect we recommend combining your laser projector with a smoke, or haze machine. This will allow you to see the beams of the laser in mid-air and will give your next party or event the WOW factor it deserves.